196
Sportster / Sportster Time Line - ความเป็นมาของ Sportster
« เมื่อ: มีนาคม 31, 2009, 10:40:23 AM »1957:
The Sportster XL was introduced as "a modern, up-to-date power plant."
55cid 7.5:1 Compression, hemi-spherical style heads, 90 degree valve angle, 4 cams
Production Information:
◦ XL (1983), $1,103
1958:
XLH introduced with higher compression and larger valves
Camshaft gears became integrated with the camshafts, eliminating the need for a woodruff key.
Drive gearshaft was enlarged .125 in.
Drive gear and second gear support shaft was enlarged .125 in and had 8 splines (instead of 6).
Choke control lever moved from left side to the air cleaner.
Heavier clutch cover and new gasket.
New oil resistant clutch hub seal and gearshaft o-ring.
Two brush generator.
Optional turn signals and 1 in over suspension.
The XLC & XLCH (Competition/California Hot)
◦ Larger ports and valves
◦ High domed pistons
◦ Light ended tappets
◦ Magneto ignition
Production Information:
◦ XL (579), $1,155
◦ XLH (711)
◦ XLC
◦ XLCH (239)
1959:
New dual exhaust on XLH with twin mufflers.
Nacelle headlamp on XLH
5 ¾ in headlamp with eyebrow on XLCH
Trip-o-meter on XLCH
Nylon chain tensioner
Single switch ignition on left fork
Valanced front fender
End relieved connecting rod bearings
14.5 sec ¼ mile (90 mph)
Production Information:
◦ XL (42), $1,175
◦ XLH (947), $1,200
◦ XLCH (1059), $1,285
1960:
New shock absorbers.
Production Information:
◦ Sportsters (2,765) XLH $1,225 XLCH $1,310
1961:
Creased edge on fuel tank.
Production Information:
◦ Sportsters (2014) XLH $1,250 XLCH $1,335
1962:
Aluminum upper triple tree.
XLR appeared for TT racing.
Production Information:
◦ Sportsters (1998) XLH $1,250 XLCH $1,335
1963:
Both XLH & XLCH got 1.323:1 3rd gear ratios (were 1.381)
◦ Final ratio 5.56:1 on the H
◦ Final ratio 5.85:1 on the CH
XLCH got "shorty duals"
XLCH got an ignition key and improved magneto/coil
14.3 sec ¼ mile (92 mph)
Production Information:
◦ XLH (432), $1,270
◦ XLCH (1,001), $1,355
1964:
Chrome panel for XLCH lower fork bracket.
New graphic for the XLH (oil tank).
Full width aluminum brake drum in the front.
Aluminum tappet guides.
Production Information:
◦ XLH (810), $1,295
◦ XLCH (1950), $1,360
1965:
XLH and XLCH received a 12 volt electrical system.
XLH got automatic spark advance.
Racing-type ball end levers.
High fidelity horn.
New shocks
3.7 gal fuel tank
Production Information:
◦ XLH (955)
◦ XLCH (2815)
1966:
P Cams, race developed intake ports, jumbo valves -> 60 hp
Tillotson diaphragm carb
"Ham-can" air cleaner
Carb heat insulator
Hexagonal tank badge.
Production Information:
◦ XLH (900) $1,415 XLCH (3,900) $1,411
◦ XLRTT (25)
1967:
Electric start option.
New shocks
Production Information:
◦ XLH (2,000) $1,650
◦ XLCH (2,500) $1,600
1968:
New forks (damping and travel) and the fork boots were canned.
Kick start was dropped from the XLH.
Restyled primary cover.
Peanut tank was an option on the XLH
Production Information:
◦ XLH (1,975) $1,650
◦ XLCH (4,900) $1,600
1969:
First use of the exhaust crossover pipe (increases hp by 5 to 58 hp) with stacked duals
New head castings.
Safety bead wheel rims.
Production Information:
◦ XLH (2,700) $1,765
◦ XLCH (5,100) $1,698
1970:
XLH got the headlamp eyebrow of the XLCH
Optional boat tail (again in 71)
Magneto ignition on the XLCH replaced with XLH's points/coil.
First year for XR-750
Production Information:
◦ XLH (3,033)
◦ XLCH (5,527)
1971:
Wet clutch with single spring.
Points and condenser moved behind plate on timing case cover.
Production Information:
◦ XLH (3,950)
◦ XLCH (6,825)
1972:
The 61 cid (called a 1000cc) XL replaced the 900.
Rated for 61 hp, 9:1 CR, 110+mph, 13.38 sec ¼ mile (97.7 mph), and 43 mpg.
Bendix/Zenith carb.
Wet clutch.
New oil pump.
Oil tank placed near chain
Seat is thinner w/less padding.
Production Information:
◦ XLH (7,500) $2,120
◦ XLCH (10,650)
1973:
First AMF production Harley
Mandatory turn signals.
New 35mm Kayaba forks, single disc front brakes.
Production Information:
◦ XLH (9,875)
◦ XLCH (10,825)
1974:
Throttle used return springs.
Production Information:
◦ XLH (13,295)
◦ XLCH (10,535)
◦ XR (100)
1975:
Left hand side gear shifting, right hand side rear brake (Fed mandated)
New 35mm Showa forks.
Production Information:
◦ XLH (13,515)
◦ XLCH (5,895)
1976:
Production Information:
◦ XLH (12,844)
◦ XLCH (5,238)
1977:
New cases to accommodate the left side shifting.
Frame designed for removal of oil pump with engine in frame.
XLT (touring) became available
◦ included thicker seat
◦ 3.5 gallon tank
◦ touring handle bars
◦ saddlebags from FLH
◦ geared higher
◦ windshield
XLCR was introduced at Daytona (available again in 78).
◦ cast aluminum wheels
◦ fiberglass tail section w/solo seat
◦ wrinkle black engine paint
◦ bikini fairing
◦ black siamese exhaust
◦ dual disc front brakes
◦ low bars
◦ black paint scheme [on everything]
◦ 4 gallon gas tank
◦ 68 horses, 9:1 compression, 110 mph
Production Information:
◦ XLH (12,742)
◦ XLCH (4,074)
◦ XLT (1,099)
◦ XLCR (1,923) $3,623
1978:
Cast wheels option
Front dual disc brakes
Electronic ignition
Battery and oil tank moved inboard
HD 75th anniversary model XLH
◦ Midnight black w/gold trim
◦ anniversary graphics
◦ gold aluminum wheels
Production Information:
◦ XLH (11,271)
◦ XLH Anniv model (2,323) $3,127
◦ XLCH (2,758) $3,370
◦ XLT (6)
1979:
All models got the XLCR frame and exhaust (Siamese).
XLT was dropped from the product line.
Kick starter was dropped.
Disc brakes front and rear.
Hugger model available for the first time.
Last year for XLCH
New model XLS appeared:
◦ Extended forks
◦ 16" rear wheel
◦ siamese exhaust
◦ drag bars on 3.5" risers
◦ sissy bar w/leather pouch
◦ highway pegs
◦ 2 piece seat
◦ chromed rear sprocket
Production Information:
◦ XLH (6,525)
◦ XLCH (141)
◦ XLS -(5,123)
◦ XLCR (9) (?leftover '78's?)
1980:
A 16 in wheel replaced the XLH 18 in.
Production Information:
◦ XLH (11,841) $5,867
◦ XLS (2,926)
1981:
Buy back from AMF
wire or cast wheels options, 16" or 18" rear wheel options
XLS
◦ buckhorn handlebars
◦ shorty dual exhaust
◦ 3.3 gallon, 2.2 gallon tank optional.
XLH
◦ shorter front forks
◦ 3.3 gallon optional.
Production Information:
◦ XLH (8,442)
◦ XLS (1,660)
1982:
Lighter frame
oil tank repositioned
Thicker head gasket w/lower 8:1 compression
Larger rear disc
XLS repositioned the battery
Production Information:
◦ XLH (5,015)
◦ XLS (1,261)
1983:
XLH:
◦ high bars
◦ vacuum advance (VOES?)
◦ 3.3 gallon tank option
◦ new seat
◦ less restrictive exhaust.
New model XLX-61: (built to sell for $3,995)
◦ solo seat
◦ peanut tank
◦ staggered dual exhaust
◦ speedo only
◦ 9 spoke wheels
◦ vacuum advance (VOES?)
◦ satin finish cases. {only year}
◦ six coil springs in clutch
◦ 156 watt generator
◦ loose output roller tranny
◦ output shaft oil seal secured by a bolt on cover
◦ 3 generator drive gears
◦ 10" dual front disc brakes.
New model - XR-1000, based on XLX chassis
◦ aluminum SR style heads w/intake ports on right, exhaust on left
◦ polished and bored by Jerry Branch
◦ helicoil inserts where rocker boxes bolt to head,
◦ 9:1, XR pistons
◦ light aluminum pushrods
◦ eccentric rocker shafts adjust valve lash
◦ iron cylinders (shortened half an inch to make room for the 'Branch' heads)- w/through bolts
◦ vacuum advance-V-fire III breaker less ignition
◦ twin 36mm Dell'Orto carbs
◦ satin textured cases
◦ 9 spoke cast wheels
◦ oiled felt air filter
◦ The XR-1000 had 71HP @ 5,600 rpm, 125 mph, 490 lbs
◦ 2.5 gallon tank, 2.5 quart oil capacity $6,995.
Production Information:
◦ XLX-61 (4,892) $3,995
◦ XLH (2,230)
◦ XLS (1,616)
◦ XR-1000 (1,018) $6,995
1984:
Diaphragm spring clutch (mid year)
Generator replaced by the alternator. (mid year)
XLH used the Peanut tank again.
XR, improved brakes, orange/black HD racing color option
XLH/X/S Single (larger) front disc.
Production Information:
◦ XLX-61 (4,284)
◦ XLH (4,442)
◦ XLS (1,135)
◦ XR-1000 (759)
1985:
Production trimmed in anticipation of the Evo XL.
Production Information:
◦ XLX-61 (1,824)
◦ XLH (4,074)
◦ XLS (616)
1986:
First year of the Evo Sportster
came in 883 and 1100cc flavors
XLX frame
Aluminum heads and cylinders
hydraulic lifters
34mm fixed-venturi Keihin carb
powder coat frame paint
cast aluminum wheels
solo seat
low bars
speedo only
turn signals double as running lights
30" seat height
Upgrade package=special paint and trim.
Production Information:
◦ XLH 883 (8,026) $3,995 XLH 883 (2,322) (upgrade) XLH 1,100 (3,077) $5,199 XLH 1,100 (954) 'Liberty'
1987:
Sportsters 30th Anniversary
first year for the Evo Hugger:
◦ The fork tubes were shortened 2"
◦ revised shock angle
◦ a softer seat at 26.75", (1.75" lower than standard)
Production Information:
◦ XLH 883 (4,990)
◦ XLH 883 (2,106) 'Hugger'
◦ XLH 883 (2,260) (upgrade)
◦ XLH 1,100 (4,018)
◦ XLH 1,100 (600) 'Anniversary'
1988:
new 39mm Fork Tubes replaced the older 35mm unit
new 40mm constant velocity Keihin slide carb
first year for the 1200 (replacing the 1100)
Production Information:
◦ XLH 883 (5,387)
◦ XLH 883 (4,501) 'Hugger'
◦ XLH 883 (1,893) 'Sportster Deluxe'
◦ XLH 1,200 (4,752)
1989:
kickstand repositioned father rearward
price increase jumped from $3995 to $3999 for the base model 883
Production Information:
◦ XLH 883 (6,142)
◦ XLH 883 (4,467) 'Hugger'
◦ XLH 883 (1,812) 'Sportster Deluxe'
◦ XLH 1,200 (4,546)
1990:
new paper air filter and paint options
40mm Keihin carb - constant velocity w/accelerator pump
Production Information:
◦ XLH 883 (5,227) $4,250
◦ XLH 883 (4,040) 'Hugger'
◦ XLH 883 (1,298) 'Sportster Deluxe'
◦ XLH 1,200 (4,598)
1991:
5 speed tranny replaced the 4 speed
belt drive replaced chain on 883 deluxe and 1200 models
hydraulic lifters were replaced with automotive type units
oil pump given internal cast feed lines
breather system moved from the crankcase to the heads (umbrella valves)
alternator moved from behind clutch to the crankshaft
primary cover redesigned
new foot peg mounts
old Dunlop k-291 tires replaced with K402's
Self canceling signals
right side timing hole
tappet blocks, rear motor mount, oil filter integrated with case
one piece push rod tubes
Production Information:
◦ XLH 883 (4,922) $4,359
◦ XLH 883 (3,487) 'Hugger'
◦ XLH 883 (3,034) 'Sportster Deluxe'
◦ XLH 1,200 (6,282) $6,245
1992:
Hugger model made even lower
standardized hand controls
Production Information:
◦ XLH 883 $4,499
◦ XLH 883 'Hugger' $5,075
◦ XLH 883 'Sportster Deluxe' $5,559
◦ XLH 1,200 $6,400
1993:
belt drive now on all Sportster models
Production Information:
◦ XLH 883 $4,775
◦ XLH 883 'Hugger' $5,420
◦ XLH 883 'Sportster Deluxe' $5,820
◦ XLH 1,200 $6,800
1994:
Oil tank revised (visually identified by relocated oil drain line which now runs to the frame instead of nipple on underside of battery tray)
Derby cover revised from small cover over center of clutch to large 4-bolt cover (with this came a new quick-release clutch cable)
Revised rear struts with chromed steel covers.
New electrical system (wiring harness/weatherproof electrical connectors, new electrical component tray under the seat)
883s got an aluminum lower triple clamp which was previously stock on only the 1200s
1995:
New Larger standard gas tank (3.25 gal) on 1200 models
Vacuum operated petcock added to Sportster line
Ignition switch moved to steering column (because of petcock)
Switched to electric speedo
Production Information:
◦ XLH 883 $4,995
◦ XLH 883 'Hugger' $5,700
◦ XLH 883 'Sportster Deluxe' $6,120
◦ XLH 1,200 $7,200
1996:
Switchgear revised, more rounded style
First year for 1200 Custom and Sport models
Production Information:
◦ XLH 883 $5,095
◦ XLH 883 'Hugger' $5,760
◦ XLH 1,200 $7,360
◦ XLH 1,200 '1200C Custom' $7,910
◦ XLH 1,200 '1200S Sport' $8,360
1997:
New Larger standard gas tank (3.25 gal) on 883 models
1998:
Revised ignition system (single fire)
1200S gets dual-plug heads (along with hotter cams)
1999:
First year of the 883C
2000:
First year for sealed wheel bearings
First year for 4-piston calipers
Pressed together flywheel assembly (supposed to be stronger and hold it's trueness better)
2001:
2002:
First year for the 883R
Introduction of the bullet-style turn signals across the line
2003:
Final year for solid mount models
New style mirrors.
Special Harley-Davidson 100th Anniversary paint/badges
2004:
Engine is rubber mounted
Trap door transmission eliminated (cases must now be split to access transmission).
Oil tank is mounted further under the seat
Seat height is lowered by an inch
Rear tire width increased to 150 mm
Custom models get 4.5 gallon gas tanks
New air cleaner cover
Brake calipers, master cylinder, switch housings and handgrips replaced, now exclusive to Sportster models.
2005:
Swing arm & rear wheel re-designed to accommodate 1" rear axle.